Songshun Steel & TOP Steel Manufacturer Supplier in China

What Details Should Be Noted in the Hot Rolling Process of XPM Die Steel Plate?

As a pre-hardened plastic mold steel boasting high purity, excellent wear resistance, high strength and other superior properties, DIN XPM steel delivers outstanding performance in various high-precision mold manufacturing fields. However, these excellent mechanical properties of XPM die steel plate can only be fully exerted through a proper hot rolling process. Therefore, strict control and meticulous attention to details are required in every step of this process. So, what key considerations should we bear in mind during the hot rolling of this steel grade?

I. Precautions Before Hot Rolling

1.1 Raw Material Screening

XPM die steel imposes an extremely high requirement on raw material purity. Excessive impurity content will directly lead to fatal defects such as scaly folding and internal blowholes on steel plates after hot rolling, which adversely impacts the post-rolling mechanical properties.

Therefore, three mandatory inspections must be completed before raw material warehousing:First, priority shall be given to high-quality scrap steel or alloy ingots with low impurity content. Spectral detection shall be conducted to verify that the chemical composition fully complies with the standard, so as to eliminate the mixing of unknown impurities.

Second, ultrasonic flaw detection shall be performed on raw materials to identify inherent defects including internal cracks, shrinkage cavities and inclusions.

Third, oil stains, rust, moisture and scale on the surface of raw materials shall be completely removed, which can be achieved by shot blasting or sand blasting processes. Otherwise, a large amount of gas will be generated during heating, resulting in defects on steel plates.

1.2 Equipment Pre-Inspection

The precision of hot rolling equipment directly affects the dimensional tolerance, thickness uniformity and surface quality of steel plates. Three categories of equipment shall be inspected with priority before startup: first, the heating furnace – calibrate the temperature sensors to ensure uniform temperature inside the furnace and avoid uneven heating of raw materials; second, the rolling rolls – check the roll surfaces for foreign debris and wear conditions, ensure the accuracy of roll gap clearance, and debug the roll bending system at the same time to prevent roll deflection from affecting plate shape during rolling; third, the descaling equipment – verify that the high-pressure water nozzles are unclogged and the water pressure meets the standard, so as to guarantee the subsequent descaling effect.

II. Key Rolling Precautions

2.1 Rolling Heating Procedure

(1) Heating Temperature

Strict attention must be paid to the heating temperature range during the rolling of XPM steel plates. Excessively high temperatures will lead to coarse grain formation, impaired uniform distribution of carbides and intensified oxidation in the material, and even thermal cracking. Conversely, insufficient temperatures will result in inadequate plasticity of the steel, making it prone to edge cracking, poor plate shape and other defects during rolling. A stage heating method is recommended with the adoption of a precise temperature control system: the steel shall first be preheated at a low temperature, then the temperature shall be raised gradually to the target value to avoid thermal shock to the steel caused by abrupt temperature rises. In addition, real-time monitoring and documentation of temperature variations are imperative.

(2) Heating Rate

The heating rate during hot rolling also requires strict control. An excessively fast heating rate will cause an excessive temperature difference between the surface and the core of the steel, leading to the formation of thermally stress-induced cracks and a surface-hot core-cold condition. Conversely, an overly slow heating rate will reduce production efficiency and increase energy consumption. It is recommended to adjust the heating rate according to the steel plate thickness to ensure uniform internal temperature of the material and complete dissolution of carbides, thereby providing favorable plastic conditions for subsequent rolling operations.

(3) Heating Time and Soaking Time

Generally, the heating time of XPM die steel shall be adjusted appropriately according to the steel thickness. Materials with greater thickness require a longer heating period to ensure uniform heat distribution. Insufficient heating time may result in uneven internal temperature, which in turn causes cracking and deformation during processing.

Special attention must also be paid to the soaking time: inadequate soaking will lead to insufficient austenitization, while excessive soaking will cause severe grain coarsening.

2.2 Rolling Pass Reduction

The rolling of XPM die steel plates shall adopt a gradient mode of rough rolling + finish rolling, following the principle of “larger reduction in early passes, smaller in later ones, with uniform decrement”: the rough rolling stage is mainly for cross-section reduction and initial forming, where a relatively high reduction ratio can be adopted, yet the rolling force must be controlled to prevent cracks caused by excessive plastic deformation of the steel; the finish rolling stage focuses on ensuring the final dimensional accuracy and surface quality, requiring a lower reduction ratio, an increased rolling speed, and precise tension control to avoid plate shape defects such as edge waves, center waves and herringbone marks.

The rolling passes and the reduction of each pass shall be rationally planned. It is necessary to ensure that the total deformation meets the specified requirements, while avoiding the fracture of the rolled piece or overload of the rolling mill caused by an excessively large single-pass reduction.

2.3 Rolling Speed

The rolling speed shall be dynamically adjusted according to the thickness of XPM die steel plate and the finishing rolling temperature. High-speed rolling is required for thin plates to reduce temperature drop, while low-speed rolling is needed for thick plates to ensure uniform deformation. In addition, by optimizing the rolling speed curve, Songshun has narrowed the fluctuation range of the finishing rolling temperature from ±15℃ to ±5℃, which significantly improves the consistency of the mechanical properties of the steel plates.

Reasonable rolling speed can not only improve production efficiency but also ensure the quality of steel plates. Therefore, sudden acceleration or deceleration shall be avoided to prevent dimensional defects such as waviness and camber on the steel plates.

III. Cooling Process After Rolling

XPM die steel plate after hot rolling shall be cooled by air cooling or water cooling, and the temperature reduction must strictly follow the preset temperature-time curve in accordance with the product performance requirements. The appropriate cooling method shall be selected specifically based on the specific specifications of the steel plates. It should be noted that an excessively fast cooling rate will lead to increased internal stress, uneven hardness and reduced toughness of the steel; an overly slow cooling rate will result in coarse grain formation, which impairs the wear resistance and hardness of the steel.

Key operational precautions are as follows: the upper and lower surfaces of the steel plates must be cooled uniformly during the cooling process to avoid deformation caused by temperature differences; meanwhile, the final cooling temperature of the steel plates shall be monitored to ensure that it meets the requirements for subsequent heat treatment.

Conclusion

In summary, meticulous control over the details of the hot rolling process for XPM die steel plate is essential, and no detail in any stage—before, during and after hot rolling—should be overlooked or neglected. At Songshun, we have a professional and complete hot rolling process flow for XPM die steel, enabling us to produce high-quality materials consistently. We are also capable of providing timely solutions to any issues encountered during the hot rolling of DIN XPM die steel plate, and we are committed to supplying high-quality, high-performance materials to customers worldwide.

Songshun Steel-Logo

Dongguan Songshun Mould Steel Co., Ltd.

Welcome to contact us at any time through the following ways
Or you can email directly to  sales@songshunsteel.com