Songshun Steel & TOP Steel Manufacturer Supplier in China

Practical Solutions for ESR Process of XPM ESU Steel

In the metal smelting industry, the electroslag remelting (ESR) process for XPM mold steel, as a high-end smelting technology, is hailed as “the ultimate means of metal purification”. However, in the actual operation of the electroslag remelting process for XPM ESU steel, numerous challenges may be encountered, which require targeted solutions to achieve technological breakthroughs. Then, what are the main problems faced in the electroslag remelting process of this steel? And how can these problems be solved? Based on Songshun’s years of production experience, this paper will conduct an in-depth discussion on these core issues and corresponding solutions.

Common Problems and Solutions in the ESR Process

1. Slag System Design and Control

  • 1.1 Problems: Irrational design and improper composition control of the slag system for XPM ESU steel, coupled with volatilization issues, lead to substandard deoxidation and desulfurization effects, failure in controlling non-metallic inclusions, impure molten steel, excessive content of harmful elements, and an abnormal increase in power consumption, among other issues.
  • 1.2 Cause Analysis:
    (1) Unstable oxides in the slag system increase the oxygen content in the molten steel.
    (2) The reduction reaction of Al₂O₃ in the traditional slag system results in an abnormal rise in aluminum content.
    (3) Mismatched electrical conductivity of the slag system causes arc instability, short circuits, splashing and other problems.
  • 1.3 Solutions:
    (1) In terms of formulation, prioritize the use of fluoralkaline slag systems with low hydrogen and low pollution, reduce the proportion of easily volatile components in slag materials, strictly control the purity of slag materials, and improve the high-temperature stability of the slag system. Meanwhile, control the particle size of slag materials to avoid aggravated volatilization caused by an excessive amount of fine powder.
    (2) Upgrade the sealed mold and gas extraction system to reduce the escape of volatile substances. Simultaneously, apply a covering agent on the surface of the slag layer to reduce the contact area between the slag and air, thereby effectively inhibiting volatilization.
    (3) Realize real-time monitoring of the slag bath composition, regularly supplement the lost components of slag materials, and dynamically adjust the slag system composition to adapt to the requirements of different steel grades. This ensures the stable performance of the slag system and guarantees the refining effect.

2. Non-Metallic Inclusions

  • 2.1 Problems: In the actual production of DIN XPM steel via the electroslag remelting process, issues such as excessive content and irregular morphology of non-metallic inclusions in ingots have been identified. These defects damage the continuity of the steel matrix, leading to a reduction in the plasticity and toughness of the steel material.
  • 2.2 Cause Analysis:
    (1) Irrational selection of the slag system results in insufficient adsorption and dissolution capacity for inclusions.
    (2) Instability of the molten slag composition and volatilization at high temperatures cause the attenuation of refining efficiency.
    (3) Inadequate contact between metal droplets and molten slag leads to the solidification of steel before the complete removal of inclusions.
    (4) Insufficient electromagnetic stirring results in a low renewal rate at the steel-slag interface and inadequate floating time for inclusions to separate out.
  • 2.3 Solutions:
    (1) Scientifically optimize the slag system formulation to enhance its adsorption capacity for inclusions.
    (2) Control the stability of the molten slag by strictly regulating the proportion of slag materials to ensure the basicity of the slag system, thereby improving the desulfurization and inclusion removal efficiency. Reduce the content of components with high vapor pressure in the slag to minimize volatilization loss at high temperatures; if necessary, apply a covering agent to reduce volatilization and gas absorption on the slag surface.
    (3) Regulate the melting rate by adjusting the current and voltage to achieve homogenized solidification of a shallow and flat slag bath, increase the contact area and contact time between metal droplets and molten slag, and improve the efficiency of slag washing and refining. Install an additional rotating magnetic field device at the bottom of the mold, which can increase the flow rate of the molten pool by 30% and shorten the floating time of inclusions to 8 minutes.

3. Shrinkage Cavities, Porosity and Center Segregation

  • 3.1 Problems: Solidification defects such as shrinkage cavities, porosity and center segregation constitute another major challenge in the electroslag remelting (ESR) process of XPM steel. These defects tend to cause cracks during subsequent processing and fail to meet the stringent mechanical property requirements of precision molds.
  • 3.2 Cause Analysis:
    (1) Uneven temperature distribution in the molten pool and mismatched cooling intensity lead to inhomogeneous solute distribution and insufficient shrinkage during the solidification of molten steel.
    (2) Improper control of the melting rate is prone to the formation of constitutional supercooling zones.
  • 3.3 Solutions:
    (1) Leverage an intelligent control system to monitor parameters such as current, voltage and electrode melting rate in real time, and precisely control the melting rate within a reasonable range. This prevents excessively high molten pool temperature caused by an overcurrent or insufficient molten pool temperature due to an undercurrent.
    (2) Optimize the cooling system by adjusting the cooling water flow of the mold according to the composition of XPM ESU steel, forming a stable temperature gradient. This promotes the directional solidification of molten steel from bottom to top and reduces center segregation.
    (3) For large XPM steel ingots, conductive mold technology can be adopted to alter the heat distribution mode, reduce the molten pool depth, obtain a more uniform and fine columnar crystal structure, and significantly lower the risks of shrinkage cavities and porosity.

Conclusion

In addition to the several core common issues outlined above, various other challenges and problems may arise during the electroslag remelting (ESR) process of XPM ESU steel. With its extensive experience and professional team, Songshun is capable of providing customized solutions. Moreover, we pay meticulous attention to numerous details in every stage of the XPM ESU material production process, and are committed to manufacturing high-end steel products to help you overcome the technical bottlenecks in steel production!

Songshun Steel-Logo

Dongguan Songshun Mould Steel Co., Ltd.

Welcome to contact us at any time through the following ways
Or you can email directly to  sales@songshunsteel.com