Songshun Steel & TOP Steel Manufacturer Supplier in China

Full Analysis of H13 Hot-Work Die Steel Surface Treatments: Nitriding, PVD Coating, Boronizing & Laser Surface Treatment

AISI H13 (equivalent to DIN 1.2344, JIS SKD61 and Chinese GB 4Cr5MoSiV1) is a widely-used hot-work die steel. It is commonly applied under working conditions subject to high temperature, impact, wear and thermal cycling. To prevent component failures under such service conditions and meet stringent requirements for broader application scenarios, surface treatment processes are adopted for H13 hot-work die steel to substantially improve its comprehensive material properties. This article takes an in-depth look at several core surface treatment technologies for H13 material.

Ⅰ. Why Perform Surface Treatment on H13 Hot-Work Die Steel?


H13 steel delivers decent hot strength and toughness after quenching and tempering. Nevertheless, hot‑work dies operate under extremely harsh service conditions, and their surfaces are constantly exposed to multiple challenges. Under such circumstances, die failure rarely results from insufficient bulk hardness; instead, it is mainly caused by thermal‑fatigue cracking, abrasive wear failure, corrosion, oxidation and other issues. These problems further lead to reduced production efficiency and higher operational costs.

The primary purpose of surface treatment for H13 hot-work die steel is to enhance surface hardness, wear resistance, corrosion resistance and fatigue resistance of the die, so as to extend die service life and boost production efficiency. In addition, surface treatment can lower the surface friction coefficient of dies, cut energy consumption and improve product quality. Therefore, selecting an appropriate surface‑treatment process is critical to the application of H13 mold steel.

Ⅱ. What Surface Treatment Processes Are Available for H13?


2.1 Gas / Plasma / Ion Nitriding

Ion nitriding is the most widely‑used surface strengthening process for H13 hot-work dies. By means of glow discharge, nitrogen ions bombard the workpiece surface and penetrate into the surface layer at a low temperature of 500-580 °C to form a nitrided layer. Common variants include gas nitriding, ion nitriding (plasma nitriding) and salt‑bath nitriding.

Objectives: To form a nitride white‑layer and diffusion layer on the surface, so as to remarkably improve surface hardness, wear resistance, thermal‑fatigue resistance and anti‑sticking performance. Ion nitriding enables precise control over case depth and microstructure.

Process Procedure:
1. Pre‑treatment: Degrease and clean the die. The die must be quenched and multi‑tempered to target hardness, finish‑machined to final dimensions, degreased and derusted, then ultrasonically cleaned in anhydrous ethanol and dried.
2. Loading into furnace: Place workpieces evenly to ensure gas circulation and avoid stacking or overlapping.
3. Heating and holding: After loading dies into the furnace, introduce ammonia gas (for gas nitriding) or apply voltage (for ion nitriding). Hold at 500 °C‑580 °C for several to tens of hours. Control ammonia dissociation rate in two phases: nitriding boost and diffusion.
4. Cool down below a specified temperature range, then unload for air cooling or oil cooling.

Special Notes:

  • Nitriding temperature for H13 must be lower than its tempering temperature; otherwise, substrate hardness will decrease.
  • The nitrided case is thin and cannot be heavily ground. If subsequent die rework is required, denitrifiable treatment or local nitriding should be adopted.
  • An excessively thick white‑layer is highly brittle and prone to spalling under thermal shock.

2.2 PVD Coating

Physical Vapor Deposition (PVD) atomizes target materials under vacuum conditions, which are then deposited onto die surfaces to form micro‑scale hard thin‑films. It is currently the mainstream surface technology for high‑end precision dies. Common coatings include TiN, CrN, TiAlN, AlCrN, AlTiN and others.

Objectives: Coating technology can remarkably enhance die performance in terms of high hardness, high‑temperature oxidation resistance, wear resistance and corrosion resistance. Meanwhile, it reduces friction coefficient and extends die service life. Furthermore, PVD coatings improve die release performance, mitigate die sticking and severe wear issues, and boost production efficiency.

Process Procedure:
1. Finish‑machine the die to mirror finish, thoroughly clean and degrease to remove all micro‑impurities.
2. Load the die into the vacuum coating chamber and evacuate to high vacuum.
3. Perform ion bombardment cleaning to activate the surface.
4. Introduce reactive gases (nitrogen, argon); evaporate target materials via arc discharge or magnetron sputtering.
5. Ions impinge on the die surface at high velocity under electric‑field action and deposit to form super‑hard coatings.
6. Cool down, unload from chamber and conduct inspection.

Special Notes:

  • Do not apply PVD coating onto H13 substrates without proper tempering treatment.
  • H13 hot‑work die steel is frequently pre‑nitrided prior to PVD treatment. Since PVD coatings are inherently thin, insufficient surface hardness of the H13 substrate may lead to plastic deformation, cracking or spalling of the coating under applied loads.

2.3 Boronizing Treatment

Boronizing enables boron atoms to diffuse into the steel surface and form boride layers of FeB and Fe₂B. Its hardness is far higher than that obtained by nitriding, making it a solution for service conditions with extreme wear.

Objectives: It can drastically improve the surface hardness of H13 tool steel, delivering excellent wear resistance, melt‑erosion resistance, high‑temperature oxidation resistance and corrosion resistance.

Process Procedure:
1. Clean and dry the workpiece.
2. Bury the workpiece in boronizing agent, then pack and seal the container.
3. Heat and hold at target temperature to form Fe₂B / FeB boride layers.
4. Cool inside the furnace followed by cleaning.
5. Perform requenching and tempering. This step is mandatory because boronizing temperature exceeds the tempering temperature of AISI H13.

Special Notes:

  • The FeB phase exhibits high brittleness; a single‑phase Fe₂B layer is preferred. Improper process control may result in layer spalling. 
  • Due to high boronizing temperature, re‑heat treatment is required. It carries a high risk of dimensional distortion and is not suitable for precision dies.
  • The boronized layer is extremely hard and thin, and cannot be heavily ground. All machining operations shall be completed prior to boronizing, with machining allowance reserved in advance.

2.4 Laser Surface Strengthening Technology

Laser treatment of ASTM H13 adopts high‑energy‑density laser beam to realize rapid heating and self‑quenching, achieving surface phase‑transformation hardening, cladding or shock peening strengthening.

Objectives: It delivers a 10‑20 % hardness increment with minimal distortion. Localized treatment is available for precise control of hardened zones, suitable for local repair and strengthening of large‑size dies. In addition, laser surface strengthening for H13 hot‑work die steel features high efficiency, high precision and environmental friendliness. It can significantly improve surface hardness and wear resistance without impairing the properties of the die substrate.

Process Procedure:
Surface cleaning / blackening → flaw detection verification → laser‑beam scanning along predefined path → rapid surface heating for austenitization → self‑quenching by self‑cooling → low‑temperature tempering.

Special Notes:

  • Improper process parameters may cause surface melting or cracking; robot path planning is required for complex curved surfaces.
  • Dilution ratio control together with preheating and slow cooling is necessary to prevent cracking. The thermal‑expansion coefficient of powder shall match that of H13 steel.

Ⅲ. FAQs on Surface Treatment of H13 Hot‑Work Die Steel


Q1: Which surface treatments are suitable for aluminum die‑casting dies and hot forging dies respectively?

A: For aluminum/magnesium die‑casting dies, PVD (TiAlN / AlCrN) or “nitriding + oxidation” is the preferred option. For extreme‑wear applications such as hot forging and extrusion, TD treatment or nitriding is recommended. Ion nitriding offers cost‑effective general‑purpose wear resistance. Hard chromium plating or oxidation is selected when high corrosion resistance and surface appearance are prioritized.

Q2: Can H13 dies be polished after nitriding?

A: Light polishing is acceptable to remove the surface porous layer, yet large‑allowance grinding is not permitted. It is recommended to perform polishing prior to nitriding, or carry out super‑finishing polishing after nitriding.

Q3: Can carburizing be applied to H13 hot‑work tool steel?

A: Not recommended. As H13 is a medium‑carbon alloy steel, carburizing involves high processing temperature and causes heavy distortion; it will also degrade core toughness. For hot‑work die strengthening, nitriding rather than carburizing is almost universally adopted.

Q4: What is the difference between QPQ and nitriding?

A: QPQ is a composite process consisting of nitrocarburizing + polishing + oxidation. Apart from hardening, it greatly improves corrosion resistance and surface finish. Conventional nitriding focuses merely on hardening. The compound layer of QPQ is denser, while its high‑temperature stability is inferior to that of the nitrided diffusion layer.

Conclusion


In addition to the processes mentioned above, surface‑treatment technologies for H13 hot-work die steel also include thermal spraying, hard chromium plating, shot peening strengthening, oxidation treatment, TD treatment, QPQ salt-bath composite treatment and so forth. Surface treatment for this steel is not a standardized single procedure, but a system engineering solution based on actual service conditions. Each technology has its well‑defined application limits. Above all, nitriding of AISI H13 hot‑work die steel stands out as the most classic, cost‑effective and widely adopted process. Mastery of these diverse processes helps satisfy market demands and achieve competitive advantages.

Looking for one‑stop solutions for H13 steel including ready‑to‑ship stock, heat treatment and surface treatment?

As a professional H13 die steel manufacturer, Songshun Steel carries multi‑specification stocks and provides supporting services such as quenching‑and‑tempering, nitriding and PVD coating. Share your service conditions with us, and we will match the most cost‑efficient surface‑treatment solution for your application.

Related Articles


Songshun Steel-Logo

Dongguan Songshun Mould Steel Co., Ltd.

Welcome to contact us at any time through the following ways
Or you can email directly to  sales@songshunsteel.com